randall
2002-12-01, 16:36:45
sry, wenn es der falsche topic ist, ich dachte es währe der geieignete da ich kein topic mit routing gefunden habe ;)
hi
ich hab das prog gesaugt, alles soweit klar diskette funzt auch
aber jetzt hab ich ein problem das werde ich net los
wie kann ich bie einen alten 386 die irq werte ändern von einer
3Com EtherLink III 3c5X9B-TPC
beim booten zeigt es an dass ich bei der 1. eth. irq 11 hab und bei der 2. eth. genauso 11
wie kann ich das ändern? ich hab auch schon ausprobiert indem ich den isa steckplatz wechsel, aber funzt net, muss ich jetzt was in der base.txt umschreiben?
meine lautet so:
##-----------------------------------------------------------------------------
## base.txt - fli4l configuration parameters 2.0.6
##
##
## P L E A S E R E A D T H E D O C U M E N T A T I O N ,
## S E E R E A D M E . T X T
##
## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N
## L E S E N , S I E H E R E A D M E . T X T
##
## Creation: 26.06.2001 fm
## Last Update: $Id: base.txt,v 1.20.2.6 2002/09/30 05:19:19 rresch Exp $
##
## Copyright (c) 2001-2002 Frank Meyer <frank@fli4l.de>
##
## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; either version 2 of the License, or
## (at your option) any later version.
##-----------------------------------------------------------------------------
#------------------------------------------------------------------------------
# General settings:
#------------------------------------------------------------------------------
HOSTNAME='fli4l' #name of fli4l router
PASSWORD='danke dass du mir hilfst' #password for telnetd, ftpd and sshd
MOUNT_BOOT='rw' #mount boot device (floppy): ro, rw, no
RAMSIZE='2048' #size of ramdisk for unzipped opt.tgz
# the variables MOUNT_OPT, PART_OPT and UPDATE_MODE will be ignored if
# RAMSIZE is not empty. see docu
MOUNT_OPT='ro' #mount opt device: ro, rw
PART_OPT='hda2' #location of opt-files? ram1 or disk-partition
UPDATE_MODE='full' #add, cfg, full, none, see documentation
#------------------------------------------------------------------------------
# Ethernet card drivers:
# uncomment your ethernet card
#------------------------------------------------------------------------------
ETH_DRV_N='1' #ISA: 3COM EtherLinkIII (3c509) # number of ethernet drivers to load, usually 1
ETH_DRV_1='3c509' #ISA: NE2000 ISA clone (eg. Realtek 8019,
ETH_DRV_1_OPTION='irq=9 io=0x340,irq=10 io=0x340'
#------------------------------------------------------------------------------
# Ether networks used with IP protocol:
#------------------------------------------------------------------------------
IP_ETH_N='1' #number of ip ethernet networks, usually 1
IP_ETH_1_NAME='' #optional: other device name than ethX
IP_ETH_1_IPADDR='192.168.0.101' #IP address of your nth ethernet card
IP_ETH_1_NETWORK='192.168.0.0' #network of your LAN
IP_ETH_1_NETMASK='255.255.255.0' #netmask of your LAN
#------------------------------------------------------------------------------
# Additional routes, optional
#------------------------------------------------------------------------------
IP_DEFAULT_GATEWAY='' #normally not used, read documentation!
IP_ROUTE_N='0' #number of additional routes
IP_ROUTE_1='192.168.7.0 255.255.255.0 192.168.6.99'# network netmask gateway
#------------------------------------------------------------------------------
# Masquerading:
#------------------------------------------------------------------------------
MASQ_NETWORK='192.168.0.0/24' #networks to masquerade (e.g. our LAN)
MASQ_MODULE_N='1' #load n masq modules (default: only ftp)
MASQ_MODULE_1='ftp' #ftp
MASQ_MODULE_2='h323' #h323 (netmeeting)
MASQ_MODULE_3='icq' #icq (use with caution!)
MASQ_MODULE_4='irc' #irc
MASQ_MODULE_5='raudio' #raudio
MASQ_MODULE_6='vdolive' #vdolive
MASQ_MODULE_7='quake' #quake
MASQ_MODULE_8='cuseeme' #cuseeme
MASQ_MODULE_9='mms' #MSN-Filetransfer
MASQ_MODULE_10='pptp' #pptp
MASQ_MODULE_11='ipsec' #ipsec
MASQ_MODULE_12='dplay' #dplay (direct play)
MASQ_MODULE_13='msn-0.02' #msn zone (use version 0.01 or 0.02)
MASQ_MODULE_14='udp_dloose' #pseudo mod: some internet games need it
MASQ_FTP_PORT_N='0' #using ftp masq-module on different ports
MASQ_FTP_PORT_1='21' #standard ftp port
MASQ_FTP_PORT_2='2021' #additional port
#------------------------------------------------------------------------------
# Optional package: PORTFW
#
# If you set OPT_PORTFW='yes', you can also edit opt/etc/portfw.sh
#------------------------------------------------------------------------------
OPT_PORTFW='no' #install port forwarding tools/modules
PORTFW_N='0' #how many portforwardings to set up
PORTFW_1='8080 192.168.6.15:80 tcp' #sample 1: forward ext. port 8080 to int.
# host 192.168.6.15 to port 80 (use tcp)
PORTFW_2='3000-3010 192.168.6.15 tcp' #sample 2: forward portrange to int. host
# 192.168.5.15 (use tcp)
#------------------------------------------------------------------------------
# Routing without masquerading
#------------------------------------------------------------------------------
ROUTE_NETWORK='' #optional: route from/to network, no masq
#------------------------------------------------------------------------------
# Routing: internal hosts to deny forwarding
#------------------------------------------------------------------------------
FORWARD_DENY_HOST_N='0' #number of denied hosts
FORWARD_DENY_HOST_1='192.168.6.5' #optional: 1st denied host
FORWARD_DENY_HOST_2='192.168.6.6' #optional: 2nd denied host
#------------------------------------------------------------------------------
# Routing: ports to reject/deny forwarding (from inside and outside!)
#------------------------------------------------------------------------------
FORWARD_DENY_PORT_N='1' #no. of ports to reject/deny forwarding
FORWARD_DENY_PORT_1='137:139 REJECT' #deny/reject forwarding of netbios
FORWARD_TRUSTED_NETS='' #but allow forwarding between LANs
#------------------------------------------------------------------------------
# Firewall: ports to reject/deny from outside (all served ports)
#
# here we leave two ports untouched:
#
# 53 dns
# 113 auth
#------------------------------------------------------------------------------
FIREWALL_DENY_PORT_N='6' #no. of ports to reject/deny
FIREWALL_DENY_PORT_1='0:52 REJECT' #privileged ports: reject or deny
FIREWALL_DENY_PORT_2='54:112 REJECT' #privileged ports: reject or deny
FIREWALL_DENY_PORT_3='114:1023 REJECT' #privileged ports: reject or deny
FIREWALL_DENY_PORT_4='5000:5001 REJECT' #imond/telmond ports: reject or deny
FIREWALL_DENY_PORT_5='8000 REJECT' #proxy access: reject or deny
FIREWALL_DENY_PORT_6='20012 REJECT' #vbox server access: reject or deny
FIREWALL_DENY_ICMP='yes' #deny icmp (ping): yes or no
FIREWALL_LOG='yes' #log access to rejected/denied ports
#------------------------------------------------------------------------------
# Domain configuration:
#------------------------------------------------------------------------------
START_DNS='yes' #start dns server: yes or no
DNS_FORWARDERS='192.76.144.66' #DNS servers of your provider, e.g. MSN
DNS_VERBOSE='no' #log queries in /usr/local/ens/ens.log
DOMAIN_NAME='lan.fli4l' #your domain name
DNS_FORBIDDEN_N='0' #number of forbidden domains
DNS_FORBIDDEN_1='foo.bar' #1st forbidden domain
DNS_FORBIDDEN_2='bar.foo' #2nd forbidden domain
HOSTS_N='5' #number of hosts in your domain
HOST_1='192.168.0.101 fli4l' #1st host: ip and name
HOST_2='192.168.0.102 client1' #2nd host: ip and name
HOST_3='192.168.0.103 client2' #3rd host: ip and name
HOST_4='192.168.0.104 client3' #4rd host: ip and name
HOST_5='192.168.0.105 client4' #5rd host: ip and name
#------------------------------------------------------------------------------
# Special DNS configuration
#------------------------------------------------------------------------------
DNS_N='0' #number of special dns servers, normally 0
#DNS_1='firma.de 192.168.1.12' # 1st special dns server for firma.de
#DNS_2='lan.firma.de 192.168.2.12' # 2nd special dns server for lan.firma.de
#------------------------------------------------------------------------------
# imond configuration:
#------------------------------------------------------------------------------
START_IMOND='yes' #start imond: yes or no
IMOND_PORT='5000' #TCP-Port, see also FIREWALL_DENY_PORT_x!
IMOND_PASS='' #imond-password, may be empty
IMOND_ADMIN_PASS='' #imond-admin-password, may be empty
IMOND_LED='' #tty for led: com1 - com4 or empty
IMOND_BEEP='yes' #beep if connection going up/down
IMOND_LOG='no' #log /var/log/imond.log: yes or no
IMOND_LOGDIR='/var/log' #log-directory, e.g. /var/log
IMOND_ENABLE='yes' #accept "enable/disable" commands
IMOND_DIAL='yes' #accept "dial/hangup" commands
IMOND_ROUTE='yes' #accept "route" command
IMOND_REBOOT='yes' #accept "reboot" command
#------------------------------------------------------------------------------
# Generic circuit configuration:
#------------------------------------------------------------------------------
IP_DYN_ADDR='yes' #use dyn. ip addresses (most providers do)
DIALMODE='auto' #standard dialmode: auto, manual, or off
#------------------------------------------------------------------------------
# optional package: syslogd
#------------------------------------------------------------------------------
OPT_SYSLOGD='no' #start syslogd: yes or no
SYSLOGD_DEST_N='1' #number of destinations
SYSLOGD_DEST_1='*.* /dev/console' #nth prio & destination of syslog msgs
SYSLOGD_DEST_2='*.* @192.168.6.2' #example: loghost 192.168.6.2
SYSLOGD_DEST_3='kern.info /var/log/dial.log'# example: log infos
#------------------------------------------------------------------------------
# optional package: klogd
#------------------------------------------------------------------------------
OPT_KLOGD='no' #start klogd: yes or no
#------------------------------------------------------------------------------
# optional package: y2k correction
#------------------------------------------------------------------------------
OPT_Y2K='no' #y2k correction: yes or no
Y2K_DAYS='' #correct hardware Y2K-Bug: add x days
#------------------------------------------------------------------------------
# Optional package: PNP
#------------------------------------------------------------------------------
OPT_PNP='no' #install isapnp tools: yes or no
hi
ich hab das prog gesaugt, alles soweit klar diskette funzt auch
aber jetzt hab ich ein problem das werde ich net los
wie kann ich bie einen alten 386 die irq werte ändern von einer
3Com EtherLink III 3c5X9B-TPC
beim booten zeigt es an dass ich bei der 1. eth. irq 11 hab und bei der 2. eth. genauso 11
wie kann ich das ändern? ich hab auch schon ausprobiert indem ich den isa steckplatz wechsel, aber funzt net, muss ich jetzt was in der base.txt umschreiben?
meine lautet so:
##-----------------------------------------------------------------------------
## base.txt - fli4l configuration parameters 2.0.6
##
##
## P L E A S E R E A D T H E D O C U M E N T A T I O N ,
## S E E R E A D M E . T X T
##
## B I T T E U N B E D I N G T D I E D O K U M E N T A T I O N
## L E S E N , S I E H E R E A D M E . T X T
##
## Creation: 26.06.2001 fm
## Last Update: $Id: base.txt,v 1.20.2.6 2002/09/30 05:19:19 rresch Exp $
##
## Copyright (c) 2001-2002 Frank Meyer <frank@fli4l.de>
##
## This program is free software; you can redistribute it and/or modify
## it under the terms of the GNU General Public License as published by
## the Free Software Foundation; either version 2 of the License, or
## (at your option) any later version.
##-----------------------------------------------------------------------------
#------------------------------------------------------------------------------
# General settings:
#------------------------------------------------------------------------------
HOSTNAME='fli4l' #name of fli4l router
PASSWORD='danke dass du mir hilfst' #password for telnetd, ftpd and sshd
MOUNT_BOOT='rw' #mount boot device (floppy): ro, rw, no
RAMSIZE='2048' #size of ramdisk for unzipped opt.tgz
# the variables MOUNT_OPT, PART_OPT and UPDATE_MODE will be ignored if
# RAMSIZE is not empty. see docu
MOUNT_OPT='ro' #mount opt device: ro, rw
PART_OPT='hda2' #location of opt-files? ram1 or disk-partition
UPDATE_MODE='full' #add, cfg, full, none, see documentation
#------------------------------------------------------------------------------
# Ethernet card drivers:
# uncomment your ethernet card
#------------------------------------------------------------------------------
ETH_DRV_N='1' #ISA: 3COM EtherLinkIII (3c509) # number of ethernet drivers to load, usually 1
ETH_DRV_1='3c509' #ISA: NE2000 ISA clone (eg. Realtek 8019,
ETH_DRV_1_OPTION='irq=9 io=0x340,irq=10 io=0x340'
#------------------------------------------------------------------------------
# Ether networks used with IP protocol:
#------------------------------------------------------------------------------
IP_ETH_N='1' #number of ip ethernet networks, usually 1
IP_ETH_1_NAME='' #optional: other device name than ethX
IP_ETH_1_IPADDR='192.168.0.101' #IP address of your nth ethernet card
IP_ETH_1_NETWORK='192.168.0.0' #network of your LAN
IP_ETH_1_NETMASK='255.255.255.0' #netmask of your LAN
#------------------------------------------------------------------------------
# Additional routes, optional
#------------------------------------------------------------------------------
IP_DEFAULT_GATEWAY='' #normally not used, read documentation!
IP_ROUTE_N='0' #number of additional routes
IP_ROUTE_1='192.168.7.0 255.255.255.0 192.168.6.99'# network netmask gateway
#------------------------------------------------------------------------------
# Masquerading:
#------------------------------------------------------------------------------
MASQ_NETWORK='192.168.0.0/24' #networks to masquerade (e.g. our LAN)
MASQ_MODULE_N='1' #load n masq modules (default: only ftp)
MASQ_MODULE_1='ftp' #ftp
MASQ_MODULE_2='h323' #h323 (netmeeting)
MASQ_MODULE_3='icq' #icq (use with caution!)
MASQ_MODULE_4='irc' #irc
MASQ_MODULE_5='raudio' #raudio
MASQ_MODULE_6='vdolive' #vdolive
MASQ_MODULE_7='quake' #quake
MASQ_MODULE_8='cuseeme' #cuseeme
MASQ_MODULE_9='mms' #MSN-Filetransfer
MASQ_MODULE_10='pptp' #pptp
MASQ_MODULE_11='ipsec' #ipsec
MASQ_MODULE_12='dplay' #dplay (direct play)
MASQ_MODULE_13='msn-0.02' #msn zone (use version 0.01 or 0.02)
MASQ_MODULE_14='udp_dloose' #pseudo mod: some internet games need it
MASQ_FTP_PORT_N='0' #using ftp masq-module on different ports
MASQ_FTP_PORT_1='21' #standard ftp port
MASQ_FTP_PORT_2='2021' #additional port
#------------------------------------------------------------------------------
# Optional package: PORTFW
#
# If you set OPT_PORTFW='yes', you can also edit opt/etc/portfw.sh
#------------------------------------------------------------------------------
OPT_PORTFW='no' #install port forwarding tools/modules
PORTFW_N='0' #how many portforwardings to set up
PORTFW_1='8080 192.168.6.15:80 tcp' #sample 1: forward ext. port 8080 to int.
# host 192.168.6.15 to port 80 (use tcp)
PORTFW_2='3000-3010 192.168.6.15 tcp' #sample 2: forward portrange to int. host
# 192.168.5.15 (use tcp)
#------------------------------------------------------------------------------
# Routing without masquerading
#------------------------------------------------------------------------------
ROUTE_NETWORK='' #optional: route from/to network, no masq
#------------------------------------------------------------------------------
# Routing: internal hosts to deny forwarding
#------------------------------------------------------------------------------
FORWARD_DENY_HOST_N='0' #number of denied hosts
FORWARD_DENY_HOST_1='192.168.6.5' #optional: 1st denied host
FORWARD_DENY_HOST_2='192.168.6.6' #optional: 2nd denied host
#------------------------------------------------------------------------------
# Routing: ports to reject/deny forwarding (from inside and outside!)
#------------------------------------------------------------------------------
FORWARD_DENY_PORT_N='1' #no. of ports to reject/deny forwarding
FORWARD_DENY_PORT_1='137:139 REJECT' #deny/reject forwarding of netbios
FORWARD_TRUSTED_NETS='' #but allow forwarding between LANs
#------------------------------------------------------------------------------
# Firewall: ports to reject/deny from outside (all served ports)
#
# here we leave two ports untouched:
#
# 53 dns
# 113 auth
#------------------------------------------------------------------------------
FIREWALL_DENY_PORT_N='6' #no. of ports to reject/deny
FIREWALL_DENY_PORT_1='0:52 REJECT' #privileged ports: reject or deny
FIREWALL_DENY_PORT_2='54:112 REJECT' #privileged ports: reject or deny
FIREWALL_DENY_PORT_3='114:1023 REJECT' #privileged ports: reject or deny
FIREWALL_DENY_PORT_4='5000:5001 REJECT' #imond/telmond ports: reject or deny
FIREWALL_DENY_PORT_5='8000 REJECT' #proxy access: reject or deny
FIREWALL_DENY_PORT_6='20012 REJECT' #vbox server access: reject or deny
FIREWALL_DENY_ICMP='yes' #deny icmp (ping): yes or no
FIREWALL_LOG='yes' #log access to rejected/denied ports
#------------------------------------------------------------------------------
# Domain configuration:
#------------------------------------------------------------------------------
START_DNS='yes' #start dns server: yes or no
DNS_FORWARDERS='192.76.144.66' #DNS servers of your provider, e.g. MSN
DNS_VERBOSE='no' #log queries in /usr/local/ens/ens.log
DOMAIN_NAME='lan.fli4l' #your domain name
DNS_FORBIDDEN_N='0' #number of forbidden domains
DNS_FORBIDDEN_1='foo.bar' #1st forbidden domain
DNS_FORBIDDEN_2='bar.foo' #2nd forbidden domain
HOSTS_N='5' #number of hosts in your domain
HOST_1='192.168.0.101 fli4l' #1st host: ip and name
HOST_2='192.168.0.102 client1' #2nd host: ip and name
HOST_3='192.168.0.103 client2' #3rd host: ip and name
HOST_4='192.168.0.104 client3' #4rd host: ip and name
HOST_5='192.168.0.105 client4' #5rd host: ip and name
#------------------------------------------------------------------------------
# Special DNS configuration
#------------------------------------------------------------------------------
DNS_N='0' #number of special dns servers, normally 0
#DNS_1='firma.de 192.168.1.12' # 1st special dns server for firma.de
#DNS_2='lan.firma.de 192.168.2.12' # 2nd special dns server for lan.firma.de
#------------------------------------------------------------------------------
# imond configuration:
#------------------------------------------------------------------------------
START_IMOND='yes' #start imond: yes or no
IMOND_PORT='5000' #TCP-Port, see also FIREWALL_DENY_PORT_x!
IMOND_PASS='' #imond-password, may be empty
IMOND_ADMIN_PASS='' #imond-admin-password, may be empty
IMOND_LED='' #tty for led: com1 - com4 or empty
IMOND_BEEP='yes' #beep if connection going up/down
IMOND_LOG='no' #log /var/log/imond.log: yes or no
IMOND_LOGDIR='/var/log' #log-directory, e.g. /var/log
IMOND_ENABLE='yes' #accept "enable/disable" commands
IMOND_DIAL='yes' #accept "dial/hangup" commands
IMOND_ROUTE='yes' #accept "route" command
IMOND_REBOOT='yes' #accept "reboot" command
#------------------------------------------------------------------------------
# Generic circuit configuration:
#------------------------------------------------------------------------------
IP_DYN_ADDR='yes' #use dyn. ip addresses (most providers do)
DIALMODE='auto' #standard dialmode: auto, manual, or off
#------------------------------------------------------------------------------
# optional package: syslogd
#------------------------------------------------------------------------------
OPT_SYSLOGD='no' #start syslogd: yes or no
SYSLOGD_DEST_N='1' #number of destinations
SYSLOGD_DEST_1='*.* /dev/console' #nth prio & destination of syslog msgs
SYSLOGD_DEST_2='*.* @192.168.6.2' #example: loghost 192.168.6.2
SYSLOGD_DEST_3='kern.info /var/log/dial.log'# example: log infos
#------------------------------------------------------------------------------
# optional package: klogd
#------------------------------------------------------------------------------
OPT_KLOGD='no' #start klogd: yes or no
#------------------------------------------------------------------------------
# optional package: y2k correction
#------------------------------------------------------------------------------
OPT_Y2K='no' #y2k correction: yes or no
Y2K_DAYS='' #correct hardware Y2K-Bug: add x days
#------------------------------------------------------------------------------
# Optional package: PNP
#------------------------------------------------------------------------------
OPT_PNP='no' #install isapnp tools: yes or no