PDA

Archiv verlassen und diese Seite im Standarddesign anzeigen : Laufwerksversagen steht unmittelbar bevor


icedealer
2009-12-08, 09:29:08
Hi, meine Festplatte (eine Samsung 500Gb, SATA) scheint Probleme zu machen. Windows Vista und Ubuntu melden unabhängig von einander das ein Laufwerksversagen bevorsteht.
Die Festplatte ist in drei Partitionen aufgeteilt, eine NTFS, eine ext4 und eine swap-Partition.

chkdsk hab ich vor dem Start schon ausgeführt, nur Fehler liegen nicht vor.
Ubuntu Zeigt einen Fehler unter attribute-184 an.

Das Problem trat erst auf nachdem ich die Festplatte neu partitioniert haben und beide Systeme neu aufgesetzt habe. Vorher hab ich im Bios noch AHCI aktiviert. Im Moment ist AHCI wieder deaktiviert aber der Fehler ist immer noch da.

Was soll ich jetzt machen? Dem Fehler glauben schenken und mir schonmal eine neue Festplatte bestellen oder gibts noch eine andere Lösung?

thx schon mal im Vorraus

anddill
2009-12-08, 10:08:22
Die Meldung dürfte vom SMART der Platte kommen. Wenn das im BIOS eingeschaltet ist, sollte da eigentlich schon beim Booten eine entsprechende Meldung kommen.
Diese Meldung ist jedenfalls ernst zu nehmen. Mach zumindest ein Backup, wenn Du noch keins hast.

icedealer
2009-12-08, 10:34:45
Hallo, ja du hast Recht, als AHCI noch aktiviert war hab ich beim starten, eine Meldung mit SMART bekommen.

Alles klar dann werde ich mich mal nach einer neuen Platte umschauen, das mit dem Backup ist kein Problem, ich hatte ja schon bevor ich die beiden System neu aufgesetzt habe ein Backup gemacht, ist alles auf dem Laptop :wink:

Gast
2009-12-08, 11:58:10
Poste doch mal die SMART Werte.

Unter Ubuntu geht das mit (falls die smartmontools installiert sind, wovon ich jetzt mal ausgehe)
sudo smartctl -a /dev/sda
oder b oder c, je nachdem welche Festplatte das in Deinem System ist.

Gast
2009-12-08, 12:00:29
Attribut 184 ist laut Wikipedia übrigens das hier:

End-to-End error
This attribute is a part of HP's SMART IV technology and it means that after transferring through the cache RAM data buffer the parity data between the host and the hard drive did not match.

icedealer
2009-12-08, 12:50:48
Nach smartctl -a /dev/sda
kam das hier: smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD502IJ
Serial Number: S13TJ1CQ621985
Firmware Version: 1AA01112
User Capacity: 500.107.862.016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3b
Local Time is: Tue Dec 8 12:33:47 2009 CET

==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (7452) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 125) minutes.
Conveyance self-test routine
recommended polling time: ( 14) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 086 086 011 Pre-fail Always - 5220
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 536
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 2297
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 516
13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 3
184 Unknown_Attribute 0x0033 001 001 099 Pre-fail Always FAILING_NOW 150
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 087 059 000 Old_age Always - 13 (Lifetime Min/Max 13/13)
194 Temperature_Celsius 0x0022 081 056 000 Old_age Always - 19 (Lifetime Min/Max 13/19)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 10535
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 100 099 000 Old_age Always - 28
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 2
201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 0
Warning: ATA Specification requires self-test log structure revision number = 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]


SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


Bei attribute-184 wird hier auch ein Fehler angezeigt.

Aus dem Text von Wikipedia werde ich trotzdem jetzt nicht ganz schlau, aber ich denke mal das meine HDD bald das zeitliche segnen wird.

Meine zweite, ,,Datenmüll-Festplatte", besteht den Test (smartctl -b /dev/sdb).
Das ist eine Seagate 160Gb SATA, hängt am selben controler.

Gast
2009-12-08, 14:14:40
Tja, jetzt müßte man wissen wofür Attribut 184 genau steht :D
Bleibt nur noch das Samsungtool mal laufen zu lassen.

RaumKraehe
2009-12-08, 14:26:25
Tja, jetzt müßte man wissen wofür Attribut 184 genau steht :D
Bleibt nur noch das Samsungtool mal laufen zu lassen.

Siehe 2 Posts über dir.

KinGGoliAth
2009-12-08, 15:05:33
Laufwerksversagen steht unmittelbar bevor

brace for impact!!1

http://s7.directupload.net/images/user/090807/839dzs5m.gif

;D


diagnoseprogramm von samsung runterladen (estool) und die platte im kompletttest prüfen. alles andere ist asche.