PDA

Archiv verlassen und diese Seite im Standarddesign anzeigen : Pin Abgebrochen, Festplatte, geht aber noch?!


Gast
2011-03-12, 15:11:02
Hi, leider ist von einer Festplatte ein Pin abgebrochen und das leider komplett.
Es ist dieser hier im Bild:
http://img861.imageshack.us/img861/3631/yxcyxc.jpg
laut Wikipedia ist es pin Nummer 39:
PDIAG, DASP
Passed Diagnostic vom Device 1, Drive Active/Device 1 Present, Rückmeldungen von Device 1 an Device 0 bei der Initialisierung
Was genau macht der?
Die Festplatte geht einwandfrei, oder ist das doch der Masse Pin?
Konsequenzen? Wird oder sollte als externe Festplatte benutzt werden.

Dr.Doom
2011-03-12, 15:57:23
http://img861.imageshack.us/img861/3631/yxcyxc.jpg
laut Wikipedia ist es pin Nummer 39:
PDIAG, DASP
Passed Diagnostic vom Device 1, Drive Active/Device 1 Present, Rückmeldungen von Device 1 an Device 0 bei der Initialisierung
Was genau macht der?

6.3.13 PDIAG- (Passed diagnostics)
This signal shall be asserted by Drive 1 to indicate to Drive 0 that it has
completed diagnostics. A 10K ohm pull-up resistor shall be used on this
signal by each drive.
Following a power on reset, software reset or RESET-, Drive 1 shall negate
PDIAG- within 1 msec (to indicate to Drive 0 that it is busy). Drive 1 shall
then assert PDIAG- within 30 seconds to indicate that it is no longer busy,
and is able to provide status. If Drive 1 is present, then Drive 0 shall wait
for up to 31 seconds from power-on reset, software reset or RESET- for Drive
1 to assert PDIAG-. If Drive 1 fails to assert PDIAG-, Drive 0 shall set bit
7 to 1 in the Error Register to indicate that Drive 1 failed. After the
assertion of PDIAG-, Drive 1 may be unable to accept commands until it has
finished its reset procedure and is Ready (DRDY=1).
Following the receipt of a valid Execute Drive Diagnostics command, Drive 1
shall negate PDIAG- within 1 msec to indicate to Drive 0 that it is busy and
has not yet passed its drive diagnostics. Drive 1 shall then assert PDIAG-
within 5 seconds to indicate that it is no longer busy, and is able to provide
status. Drive 1 should clear BSY before asserting PDIAG-. If Drive 1 is
present then Drive 0 shall wait for up to 6 seconds from the receipt of a
valid Execute Drive Diagnostics command for Drive 1 to assert PDIAG-. If
Drive 1 fails to assert PDIAG-, Drive 0 shall set bit 7 to 1 in the Error
Register to indicate that Drive 1 failed.
If DASP- was not asserted by Drive 1 during reset initialization, Drive 0
shall post its own status immediately after it completes diagnostics, and
clear the Drive 1 Status Register to 00h. Drive 0 may be unable to accept
commands until it has finished its reset procedure and is Ready (DRDY=1).

( Quelle (ftp://ftp.t10.org/t13/project/d0791r4c-ATA-1.pdf) )

Die Festplatte geht einwandfrei, oder ist das doch der Masse Pin?
Konsequenzen? Wird oder sollte als externe Festplatte benutzt werden.Nach flüchtigem Überfliegen des Texts komme ich zu dem Schluss: man braucht den Pin nur, wenn an der IDE-Strippe noch ein zweites Gerät hängt. ;)

Gast
2011-03-12, 16:28:24
Da bin ich ja sehr froh, danke für deine Mühe ^^